The access control system is a subsystem of the access management system. Usually, it adopts technologies such as credit card, password or human biometric identification. Under the control of the management software, it manages the entrance and exit of personnel or vehicles, so that the people who have obtained the approved entry and exit are free to pass. For those who should not go in and out, it is forbidden. Therefore, in many places where the identity of people and vehicles needs to be checked, the access control system has become an indispensable configuration item. In this issue, we will discuss the technology of access control network communication applications.
Engineering principle and transmission line
Engineering principle
The engineering principle of the access control system is basically similar to that of other automatic control systems or intelligent building systems. Its operation can be divided into three parts: sensing, management and execution, but it is relatively compact and relatively simple.
Sensing: Card readers, PIN pads, various biometric readers, exit buttons, and lock status sensors are all sensor components. Their task is to accept commands, upload signals or post-check (biometric).
Management: The controller and management software bear the management function of the access control system. After receiving the information sent by the sensor, they judge whether to open the door according to the time, card number and other information. If the door is opened, the door opening command is issued to the electric lock. When the lock status information is received, the timing starts and the timeout alarms.
Execution: When the electric lock receives a command to open or close the door (power or power off), its "execute" command adjusts the working state to match the command. The lock status sensor in the electric lock plays a role of feedback and supervision.
Some controllers can use relays to output control signals to control linked cameras and lights.
Transmission line
According to the working principle, there are several transmission lines in the access control system:
power cable
Most of the power supply of the access control system comes from the UPS in the equipment room to avoid malfunction during power failure. The power cord is usually in a 220V AC transfer mode to reduce the voltage drop across the power supply. Beside the controller, equipped with a regulated power supply, the AC 220V power supply is converted into a DC 12V power supply, which is supplied to the controller and the electric lock respectively. Most of the electric locks used in the access control system belong to the 12V DC power supply mode. At the moment when the electric lock is broken, due to the action of the electric lock middle line package (electromagnet coil), a strong current is generated in the power line, which is liable to cause power fluctuation, and this power fluctuation is extremely disadvantageous for the stable operation of the controller. Therefore, in an access control system with high reliability requirements, the controller and the electric lock respectively use different power supply modules, that is, 220V AC power supply to the controller, and the two 12V DC power supply modules are respectively rectified/regulated and respectively supplied. Electric lock and controller. The selection of various power cords is basically based on an electrician's manual, using a standard power cord.
CREE LED Grow Light can save about 30% cost in the application,mainly lie in LED package cost,light engine production costs and the secondary light distributioncosts, which is great significance for applications and promotion of semiconductor lighting. We could also DIY the led ratio(wavelength ratio) which imitate the natural sun spectrum to help your plants grow in a very natural type of atmosphere, Absolutely, we are the very original and professional OEM/ODM factory, our Cree Led Grow Light have the great cost performance with the new integration technology being used for mass production, partners around the world keep telling us how amazed at the increase in output and the decrease in the energy bill.
Applications
Our professional full spectrum Cree Led Grow Light are suitable for all the indoor plants and good for seeding, growth,flowering and fruiting stages of plants, increasing the harvest and Saving energy.
Key Features
Plug with listed certificate safe to use.
Item Display
The Plug you can choose
Full Spectrum Cree LED Grow Light PAR Value
Our Ageing Test
Package
Warnings:
1.lndoor use only.
2.To avoid being damaged,do not use water or drip irrigation while using.
3.Sunshine lighting time should be 12-18 hours.
4.While irradiating the plants,the height of led grow lamp is not less than 10 inches,low height will cause the destruction of plants.
5.Highly hang the lamp will weaken the energy and affect the growth cycle of the plants, so the lamp should not be hung too high.
6.While taking care of the plants, please spray the leaves and branches 2-3 times everyday,to ensure the the plants do not wrinkle a wither, and have no phenomenon of few fruit, and hard pericarp.
Warmly welcome to Visit our Factrory when you come to China.
Cree Led Grow Light
CREE Chips LED Grow Light,CREE LED Grow Light,CREE Grow Light,CREE COB LED Grow Light
Shenzhen Phlizon Technology Co.,Ltd. , https://www.philizon.com